Chapin 22230XP User Manual download pdf

WARNING

3. Pre-Use Check

4. Filling

1) Do: Turn pump handle counterclockwise and remove pump

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over ll to accommodate pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.

7. Care, Storage and Maintenance

010522-30 (A) R0812

WARNING: Handling the brass parts of this product will expose you to lead, a chemical known to the State of

California to cause birth defects and other reproductive harm. Wash hands after handling.

2. Nozzle

6-6136

Hose

Manguera

Tuyau

6-5370

Extension wand, Vara de extensión, Rallonge

6-5371

Shut-o Handle

Mango de cierre

Poignée du robinet

6-5372

Nozzle

Tobera

Buse

Note: Your particular sprayer may not include all parts pictured above.

Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

Repair Parts Kit Gaskets and Seals (not included),

Juego de piezas de reparación, empaquetaduras y juntas (no incluido)

Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-4601

2A 2B

P.O. Box 549 700 Ellicott St.

Batavia, NY 14021-0549 U.S.A.

1-800-950-4458 www.chapinmfg.com

1. Hose to Tank

Discharge/ Assembly

• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).

• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).

• Proper placement of white outlet tube (Fig. 1C).

• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab with notches on the tank adapter.

• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).

Discharge

Assembly

Outlet

Tube

Retaining Nut -

Securely tightened.

1C 1D

Gap

Tank

Adapter

Outlet Tube

Adapter

Tab/

Notch

Outlet Tube

Adapter

Outlet

Tube

Parts, Piezas, Pièces

Attach nozzle to shut-o handle or extension wand.

Congratulations!

You have just purchased a quality Chapin product.

Questions? Do Not Return To Store.

Call us @ 1-800-950-4458 or www.chapinmfg.com

¡Felicitaciones!

Usted acaba de adquirir un producto de calidad Chapin.

Registre su pulverizador en línea en www.chapinmfg.com

¿Preguntas? No regrese a la tienda;

llámenos al 1-800-950-4458 o visite www.chapinmfg.com

Félicitations!

Vous avez acheté un produit de qualité Chapin.

Enregistrez dès que possible votre pulvérisateur en ligne à

l'adresse suivante: www.chapinmfg.com

Questions ? Ne retournez pas au magasin.

Appelez-nous 1-800-950-4458 ou visitez le

www.chapinmfg.com

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose

before using. Replace with original manufacturer’s parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for

signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could

result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace.

Do not attempt to patch leaks, etc., as this could result in serious injury.

4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and

inspect for leaks).

5) Do: Direct shut-o away from you and open to make sure discharge is not clogged.

6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,

Pressurizing and Spraying Instructions.

7) Do: Inspect all metal parts including the wand, nozzle and ttings for rust, corrosion and pitting. If any of these

conditions are found, replace aected part with original manufacturer’s part before using.

1) Do: Rinse tank thoroughly with water only, empty, rell with water. Follow Filling, Pressurizing and Spraying

Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed with water

after each use.

2) Do: Open shut-o and allow water to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.

WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious

eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a pres-

surized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store

or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protec-

tion when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with face or

body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or solution

from striking and injuring you. Never pressurize sprayer by any means other than the original pump. Do not

attempt to modify this sprayer. Replace parts only with manufacturer’s original parts. is sprayer is designed

for acidic solutions only. Never spray ammable, chlorine or bleach, caustic, or other corrosive solutions

or heat, pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s instruc-

tions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.

Sk-1159-1

9. Troubleshooting

Tank pressurizes but does not spray.

WARNING:

Release pressure in tank before troubleshooting.

Clean Nozzle Assembly (Fig. 9E)

-Remove nozzle cap by unscrewing. Clean and re-assemble.

Clean shut-off (Fig. 9A- 9D)

Nozzle Cap

Pull handle

straight up.

Insert notches from

underside of handle

into plunger grooves

and turn counter-

clockwise.

Remove plunger. Wash

diaphragm in mild dish

detergent.

Tighten plunger clockwise until

ush to top of shut-o body. Do

not over-tighten or unit may not

spray. Slide forks under plunger,

push handle down until it snaps

into place.

9A 9B 9C

Handle

Plunger

Body

Rubber

Diaphragm

Plunger ush

with body

5. Pressurizing and Spraying

Do: Turn handle clockwise to

tighten. Push handle down, turn

1/4 turn counterclockwise to release.

Do: Pump until you

feel resistance.

Do: Push handle, down, turn 1/4 turn

clockwise to lock. Begin spraying. Re-pump

sprayer as required to maintain spray force.

6. To Release Pressure

1) Your sprayer is equipped with a pressure relief/release valve

(Fig. 6A). To release pressure lift and hold the cap until air

is completely exhausted, OR, turn the valve slowly counter

clockwise until you hear air escaping and wait air is completely

exhausted (Fig. 6B).

2) Do: Stay away from the sprayer until all air has escaped.

6A 6B

8. Wand Dock Clip

Choose the holder that ts your wand.

6-4605

Pressure Relief Valve

Válvula de descarga de presión

Soupape de décompression

1 2

Summary of Contents

Page 1 - Batavia, NY 14021-0549 U.S.A

WARNING3. Pre-Use Check4. Filling1) Do: Turn pump handle counterclockwise and remove pump2) Do: Prepare spray solution following all directions and

Page 2 - ADAVERTISSEMENT

010522-30 (B) R08123. Veriﬁcación Antes Del UsoADVERTENCIAADVERTENCIA: El manejo de las partes de latón de este producto lo expondrá al plomo, un agen

Related models: 22240XP

Comments to this Manuals

No comments

Chapin 22230XP User Manual

Browse online or download User Manual for Water equipment Chapin 22230XP. Chapin 22230XP User Manual

Summary of Contents

Related models: 22240XP

Comments to this Manuals

Related products and manuals for Water equipment Chapin 22230XP